Fortis AD 512 Standard 700g Universal Polyurethane Adhesive - Foil Sausage

FORTIS AD512

Construction Adhesive – Foil Sausage

FORTIS AD512 is a universal adhesive paste to glue concrete block, floorboards, strip flooring. yellow tongue, sound insulating rubber and traffic control tactiles.

Fortis Polyurethane adhesives have long been used in manufacturing for bonding varied substrates.
Fortis adhesives have been found to provide extremely high strength and exceptional versatility in processing they have become more popular for those wishing to increase production rates. Fortis polyurethane adhesives can be used to bond a range of substrates including steel, stainless, polystyrene, EVA foam and a large range of hardwood timbers. Fortis moisture curing polyurethane adhesives provide exceptional processing features to transport manufacturers of truck bodies, rail vehicles, caravan (RV) and 4WD bodies. Structurally approved moisture curing adhesives are best suited for glue lamination timbers and finger jointing. As a result they are currently being used on both Weinig and MTB equipment.

Each sausage is enough for 0.5m2 for a flat surface or 0.25m2 for a very rough surface.

Construction Adhesive – Foil Sausage

Universal adhesive paste to glue concrete block, floorboards, strip flooring. yellow tongue, sound insulating rubber and traffic control tactiles.

• High strength polyurethane glue
• Gap filling
• Glues timber, concrete, rubber and metal
• Can be used as a primer

See below for SDS & TDS

Pack (Bulk Box) Sizes: 12 x 700g / box

Application Notes:
Puncture foil sausage near end with a nail. Squeeze a 6mm diameter bead at suitable spacing to allow for effective coverage (at least 80% of surface to be bonded). Fasten or weight to secure during cure.
Contains <110g/l Heavy aromatic solvent. <10% Diphenylmethane 4'4 diisocyanate.

WARNING CONTAINS ISOCYANATES: This material may be harmful if swallowed, inhaled or absorbed through the skin. Avoid breathing vapour. Use with adequate ventilation. Wear suitable protective clothing, impervious gloves and eye and face protection.
If poisoning does occur, contact: National poisons centre: 131 126, After hours contact: 0439 310 299

Safety Data Sheet

Product Name: Fortis AD512 Issued: 23-08-2018 Version: 1.1 Page 1 of 8

Hazardous Chemical, NON-Dangerous Goods 1. MATERIAL AND SUPPLY COMPANY IDENTIFICATION Product name: Fortis AD512 Recommended use: Construction Polyurethane Adhesive Supplier: FORTIS ADHESIVES & COATINGS PTY LTD ABN: 65133915732 Street Address: 14 Commercial Drive, Dandenong South 3175 Victoria, Australia Telephone: +61 3 9706 5448 Facsimile: +61 3 9706 5876 Email: enquires@fortisadhesives.com.au Emergency Telephone number: 13 11 26 2. HAZARDS IDENTIFICATION This material is hazardous according to health criteria of Safe Work Australia. Signal Word Danger Hazard Classifications Acute Toxicity - Inhalation - Category 4 Skin Corrosion/Irritation - Category 2 Serious Eye Damage/Irritation - Category 2A Sensitisation - Respiratory - Category 1 Sensitisation - Skin - Category 1 Carcinogenicity - Category 2 Specific Target Organ Toxicity (Single Exposure) - Category 3 Respiratory Tract Irritation Specific Target Organ Toxicity (Repeated Exposure) - Category 2 Hazard Statements H315 Causes skin irritation. H317 May cause an allergic skin reaction. H319 Causes serious eye irritation. H332 Harmful if inhaled. H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled. H335 May cause respiratory irritation. H351 Suspected of causing cancer . H373 May cause damage to organs through prolonged or repeated exposure. Prevention Precautionary Statements P102 Keep out of reach of children. P103 Read label before use. P201 Obtain special instructions before use. P202 Do not handle until all safety precautions have been read and understood. P260 Do not breathe dust, fume, gas, mist, vapours or spray. Safety Data Sheet Product Name: Fortis AD512 Issued: 23-08-2018 Version: 1.1 Page 2 of 8 P261 Avoid breathing dust, fume, gas, mist, vapours or spray.. P264 Wash hands, face and all exposed skin thoroughly after handling. P271 Use only outdoors or in a well-ventilated area. P272 Contaminated work clothing should not be allowed out of the workplace. P281 Use personal protective equipment as required. P285 In case of inadequate ventilation wear respiratory protection. Response Precautionary Statements P101 If medical advice is needed, have product container or label at hand. P302+P352 IF ON SKIN: Wash with plenty of soap and water. P304+P340 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. P304+P341 IF INHALED: If breathing is difficult, remove victim to fresh air and keep at rest in a position comfortable for breathing. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P308+P313 IF exposed or concerned: Get medical advice/attention. P312 Call a POISON CENTRE or doctor/physician if you feel unwell. P314 Get medical advice/attention if you feel unwell. P321 Specific treatment (see product label). P332+P313 If skin irritation occurs: Get medical advice/attention. P333+P313 If skin irritation or rash occurs: Get medical advice/attention. P337+P313 If eye irritation persists: Get medical advice/attention. P342+P311 If experiencing respiratory symptoms: Call a POISON CENTRE or doctor/physician. P362 Take off contaminated clothing and wash before reuse. P363 Wash contaminated clothing before reuse. Storage Precautionary Statements P403+P233 Store in a well-ventilated place. Keep container tightly closed. P405 Store locked up. Disposal Precautionary Statement P501 Dispose of contents/container in accordance with local, regional, national and international regulations. Poison Schedule: S6. Poison DANGEROUS GOOD CLASSIFICATION Not classified as Dangerous Goods by the criteria of the "Australian Code for the Transport of Dangerous Goods by Road & Rail" and the "New Zealand NZS5433: Transport of Dangerous Goods on Land". 3. COMPOSITION INFORMATION CHEMICAL ENTITY CAS NO PROPORTION Poly[oxy(methyl-1,2-ethanediyl)], .alpha.-hydro-.omega.-hydroxy-, polymer with 1,1'-methylenebis[isocyanatobenzene] 39420-98-9 10-30 % (w/w) Polymethyl polyphenyl isocyanate 9016-87-9 10-30 % Ingredients determined to be Non-Hazardous Balance ____________ 100% 4. FIRST AID MEASURES If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia 131 126, New Zealand 0800 764 766). Safety Data Sheet Product Name: Fortis AD512 Issued: 23-08-2018 Version: 1.1 Page 3 of 8 Inhalation: Effects may be delayed. Remove victim from exposure - avoid becoming a casualty. Remove contaminated clothing and loosen remaining clothing. Allow patient to assume most comfortable position and keep warm. Keep at rest until fully recovered. If breathing laboured and patient cyanotic (blue), ensure airways are clear and have a qualified person give oxygen through a facemask. If breathing has stopped apply artificial respiration at once. In the event of cardiac arrest, apply external cardiac massage. Seek immediate medical advice. Skin Contact: Effects may be delayed. If skin or hair contact occurs, immediately remove contaminated clothing and flush skin and hair with running water. Continue flushing with water until advised to stop by the Poisons Information Centre or a Doctor; or for 15 minutes and transport to Doctor or Hospital. Eye contact: If in eyes, hold eyelids apart and flush the eyes continuously with running water. Continue flushing until advised to stop by the Poisons Information Centre or a Doctor; or for at least 15 minutes and transport to Doctor or Hospital. Ingestion: Rinse mouth with water. If swallowed, do NOT induce vomiting. Give a glass of water to drink. Never give anything by the mouth to an unconscious patient. If vomiting occurs give further water. Seek medical advice. PPE for First Aiders: Wear safety shoes, overalls, gloves, chemical goggles, respirator. Use with adequate ventilation. If inhalation risk exists wear organic vapour/particulate respirator meeting the requirements of AS/NZS 1715 and AS/NZS 1716. Available information suggests that gloves made from nitrile rubber should be suitable for intermittent contact. However, due to variations in glove construction and local conditions, the user should make a final assessment. Always wash hands before smoking, eating, drinking or using the toilet. Wash contaminated clothing and other protective equipment before storing or re-using. Notes to physician: Treat symptomatically. Effects may be delayed. 5. FIRE FIGHTING MEASURES Hazchem Code: Not applicable. Suitable extinguishing media: If material is involved in a fire use water fog (or if unavailable fine water spray), alcohol resistant foam, standard foam, dry agent (carbon dioxide, dry chemical powder). Specific hazards: Combustible material. Fire fighting further advice: On burning or decomposing may emit toxic fumes. Fire fighters to wear selfcontained breathing apparatus and suitable protective clothing if risk of exposure to vapour or products of combustion or decomposition. 6. ACCIDENTAL RELEASE MEASURES SMALL SPILLS Wear protective equipment to prevent skin and eye contamination. Avoid inhalation of vapours or dust. Wipe up with absorbent (clean rag or paper towels). Collect and seal in properly labelled containers or drums for disposal. LARGE SPILLS Clear area of all unprotected personnel. Slippery when spilt. Avoid accidents, clean up immediately. Wear protective equipment to prevent skin and eye contamination and the inhalation of dust. Work up wind or increase ventilation. Cover with damp absorbent (inert material, sand or soil). Sweep or vacuum up, but avoid generating dust. Collect and seal in properly labelled containers or drums for disposal. If contamination of crops, sewers or waterways has occurred advise local emergency services. Dangerous Goods - Initial Emergency Response Guide No: Not applicable Safety Data Sheet Product Name: Fortis AD512 Issued: 23-08-2018 Version: 1.1 Page 4 of 8 7. HANDLING AND STORAGE Handling: Avoid eye contact and skin contact. Avoid inhalation of dust. Storage: Store in a cool, dry, well-ventilated place and out of direct sunlight. Store away from foodstuffs. Store away from incompatible materials described in Section 10. Store away from sources of heat and/or ignition. Store locked up. Keep container standing upright. Keep containers closed when not in use - check regularly for spills. This material is a Scheduled Poison Schedule 6 (Poison) and must be stored, maintained and used in accordance with the relevant regulations. 8. EXPOSURE CONTROLS / PERSONAL PROTECTION National occupational exposure limits: TWA STEL NOTICES ppm mg/m3 ppm mg/m3 Isocyanates, all (as-NCO) - 0.02 - 0.07 Sen As published by Safe Work Australia. TWA - The time-weighted average airborne concentration over an eight-hour working day, for a five-day working week over an entire working life. STEL (Short Term Exposure Limit) - the average airborne concentration over a 15 minute period which should not be exceeded at any time during a normal eight-hour workday. ‘Sen' Notice - sensitiser. The substance can cause a specific immune response in some people. An affected individual may subsequently react to exposure to minute levels of that substance. These Exposure Standards are guides to be used in the control of occupational health hazards. All atmospheric contamination should be kept too as low a level as is workable. These exposure standards should not be used as fine dividing lines between safe and dangerous concentrations of chemicals. They are not a measure of relative toxicity. If the directions for use on the product label are followed, exposure of individuals using the product should not exceed the above standard. The standard was created for workers who are routinely, potentially exposed during product manufacture. Biological Limit Values: As per the "National Model Regulations for the Control of Workplace Hazardous Substances (Safe Work Australia)" the ingredients in this material do not have a Biological Limit Allocated. Engineering Measures: Ensure ventilation is adequate to maintain air concentrations below Exposure Standards. Use only in well ventilated areas. Avoid generating and inhaling dusts. Use with local exhaust ventilation or while wearing dust mask. Vapour heavier than air - prevent concentration in hollows or sumps. Do NOT enter confined spaces where vapour may have collected. Personal Protection Equipment: SAFETY SHOES, OVERALLS, GLOVES, CHEMICAL GOGGLES, RESPIRATOR. Safety Data Sheet Product Name: Fortis AD512 Issued: 23-08-2018 Version: 1.1 Page 5 of 8 Personal protective equipment (PPE) must be suitable for the nature of the work and any hazard associated with the work as identified by the risk assessment conducted. Wear safety shoes, overalls, gloves, chemical goggles, respirator. Use with adequate ventilation. If inhalation risk exists wear organic vapour/particulate respirator meeting the requirements of AS/NZS 1715 and AS/NZS 1716. Available information suggests that gloves made from nitrile rubber should be suitable for intermittent contact. However, due to variations in glove construction and local conditions, the user should make a final assessment. Always wash hands before smoking, eating, drinking or using the toilet. Wash contaminated clothing and other protective equipment before storing or re-using. Hygiene measures: Keep away from food, drink and animal feeding stuffs. When using do not eat, drink or smoke. Wash hands prior to eating, drinking or smoking. Avoid contact with clothing. Avoid eye contact and skin contact. Avoid inhalation of dust. Ensure that eyewash stations and safety showers are close to the workstation location. 9. PHYSICAL AND CHEMICAL PROPERTIES Form: Paste Colour: Grey Odour: Slight Solubility: Insoluble in water Specific Gravity: 1.2 Density: 1.1 Relative Vapour Density (air=1): >1 Vapour Pressure (20 °C): N Av Flash Point (°C): >100 Flammability Limits (%): N App Autoignition Temperature (°C): N Av Melting Point/Range (°C): N Av Boiling Point/Range (°C): 180 pH: N App Viscosity: N Av Total VOC (g/Litre): N Av (Typical values only - consult specification sheet) N Av = Not available, N App = Not applicable 10. STABILITY AND REACTIVITY Chemical stability: This material is thermally stable when stored and used as directed. Conditions to avoid: Elevated temperatures and sources of ignition. Incompatible materials: Oxidising agents. Hazardous decomposition products: Oxides of carbon and nitrogen, smoke and other toxic fumes. Hazardous reactions: No known hazardous reactions. 11. TOXICOLOGICAL INFORMATION No adverse health effects expected if the product is handled in accordance with this Safety Data Sheet and the product label. Symptoms or effects that may arise if the product is mishandled and overexposure occurs are: Safety Data Sheet Product Name: Fortis AD512 Issued: 23-08-2018 Version: 1.1 Page 6 of 8 Acute Effects Inhalation: Harmful if inhaled. Material is an irritant to mucous membranes and respiratory tract. A respiratory sensitiser. Can cause possible allergic reactions. Skin contact: Contact with skin will result in irritation. A skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. Ingestion: Swallowing can result in nausea, vomiting and irritation of the gastrointestinal tract. Eye contact: An eye irritant. Exposure to the dust may cause discomfort due to particulate nature. May cause physical irritation to the eyes. Acute toxicity Inhalation: This material has been classified as a Category 4 Hazard. Acute toxicity estimate (based on ingredients): 1.0 < LC50 ≤ 5 mg/L Skin contact: This material has been classified as non-hazardous. Acute toxicity estimate (based on ingredients): >2,000 mg/Kg bw Ingestion: This material has been classified as non-hazardous. Acute toxicity estimate (based on ingredients): >2,000 mg/Kg bw Corrosion/Irritancy: Eye: this material has been classified as a Category 2A Hazard (reversible effects to eyes). Skin: this material has been classified as a Category 2 Hazard (reversible effects to skin). Sensitisation: Inhalation: this material has been classified as a Category 1 Hazard (respiratory sensitiser). Skin: this material has been classified as a Category 1 Hazard (skin sensitiser). Aspiration hazard: This material has been classified as non-hazardous. Specific target organ toxicity (single exposure): This material has been classified as a Category 3 Hazard. Exposure via inhalation may result in respiratory irritation. Chronic Toxicity Mutagenicity: This material has been classified as non-hazardous. Carcinogenicity: This material has been classified as a Category 2 Hazard. Reproductive toxicity (including via lactation): This material has been classified as non-hazardous. Specific target organ toxicity (repeat exposure): This material has been classified as a Category 2 Hazard. 12. ECOLOGICAL INFORMATION Avoid contaminating waterways. Acute aquatic hazard: This material has been classified as non-hazardous. Acute toxicity estimate (based on ingredients): >100 mg/L Long-term aquatic hazard: This material has been classified as non-hazardous. Non-rapidly or rapidly degradable substance for which there are adequate chronic toxicity data available OR in the absence of chronic toxicity data, Acute toxicity estimate (based on ingredients): >100 mg/L, where the substance is not rapidly degradable and/or BCF < 500 and/or log Kow < 4. Ecotoxicity: No information available. Safety Data Sheet Product Name: Fortis AD512 Issued: 23-08-2018 Version: 1.1 Page 7 of 8 Persistence and degradability: No information available. Bioaccumulative potential: No information available. Mobility: No information available. 13. DISPOSAL CONSIDERATIONS Persons conducting disposal, recycling or reclamation activities should ensure that appropriate personal protection equipment is used, see "Section 8. Exposure Controls and Personal Protection" of this SDS. If possible material and its container should be recycled. If material or container cannot be recycled, dispose in accordance with local, regional, national and international Regulations. 14. TRANSPORT INFORMATION ROAD AND RAIL TRANSPORT Not classified as Dangerous Goods by the criteria of the "Australian Code for the Transport of Dangerous Goods by Road & Rail" and the "New Zealand NZS5433: Transport of Dangerous Goods on Land". MARINE TRANSPORT Not classified as Dangerous Goods by the criteria of the International Maritime Dangerous Goods Code (IMDG Code) for transport by sea. AIR TRANSPORT Not classified as Dangerous Goods by the criteria of the International Air Transport Association (IATA) Dangerous Goods Regulations for transport by air. 15. REGULATORY INFORMATION This material is not subject to the following international agreements: Montreal Protocol (Ozone depleting substances) The Stockholm Convention (Persistent Organic Pollutants) The Rotterdam Convention (Prior Informed Consent) Basel Convention (Hazardous Waste) International Convention for the Prevention of Pollution from Ships (MARPOL) This material/constituent(s) is covered by the following requirements: • The Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP) established under the Therapeutic Goods Act (Commonwealth). • All components of this product are listed on or exempt from the Australian Inventory of Chemical Substances (AICS). 16. OTHER INFORMATION Reason for issue: Revised This information was prepared in good faith from the best information available at the time of issue. It is based on the present level of research and to this extent we believe it is accurate. However, no guarantee of accuracy is made or implied and since conditions of use are beyond our control, all information relevant to usage is offered without warranty. The manufacturer will not be held responsible for any unauthorised use of this information or for any modified or altered versions. If you are an employer it is your duty to tell your employees, and any others that may be affected, of any hazards Safety Data Sheet Product Name: Fortis AD512 Issued: 23-08-2018 Version: 1.1 Page 8 of 8 described in this sheet and of any precautions that should be taken. Safety Data Sheets are updated frequently. Please ensure you have a current copy.

Advanced Group is mainly located in Keysborough (in South-East Melbourne, Victoria) however we ship all over Australia & sometimes we can ship Australia Wide for Free! For example: 1. *Free Shipping for *All online orders over $300 to Victoria, Australia. (*Bulky Orders over 999kg do not qualify) 2. *Any order to anywhere in Australia MUST have all items with the Prefix/es in the Product Codes starting with "Barr-" & the order is over $300. 3. *Any order to anywhere in Australia with all "numerical (only) Product Codes" & the order is over $300 (for example Product Code:12345). Phone & Email orders will incur shipping costs at cost.